Service History 2159 - Dan Marc Appliance (2024)

Job Details:12/26/2018

REFRIGERATOR WHIRLPOOL WRF555SDFZ08 Removed freezer door installed new gears cycle check

Job Details:12/26/2018

WASHER MAYTAG MVWC415EW1 Trans W11035747 276.96Actuator W10913953 63.22Splotch W10721967 31.91Belt WPW10006384 24.98Unit has bad trans and listed parts. 165.00Electronics and pump test ok.Gave est. customer now states he cancelled. Adv Lori.

Job Details:12/26/2018

DOUBLE WALL OVEN JENN-AIR JJW3830WS00Customer show me video of control panel turning on oven. Will need control panel and 2 boards ; ordrng 1 W11087472 (CONTROL PANEL.) and 2 WPW10292566 (OVEN CONTROL )s

Job Details:12/26/2018

M/W OTR WHIRLPOOL WMH31017HS2"+30 second feature on keypad does not work. Tried reseating connectors on control, unplugging ect. Called tech-line after having no success and was told to replace control. SR#7723760131 ; ordrng 1 W10892389 (CONTROL)"

Job Details:12/26/2018

M/W OTR WHIRLPOOL WMH78019HZ1Found unit not heating.will need high side; ordrng 1 W10561770 (CAP) and 1 W11087316 (TRANSFORM ) and 1 W1123995 (MAG) and 1 W11256462 (DIODE)

Job Details:12/26/2018

WALL OVEN JENN AIR JJW3830WS02 Installed control panel ran ovens tested ok.

Job Details:12/26/2018

COOKTOP WHIRLPOOL WFE515S0ES1TB- Unit needs replacement LF element and LF infinite switch.; ordrng 1 W10275048 (ELEMENT ) and 1 W10434452 (SWITCH)

Job Details:12/26/2018

REFRIG/FREEZER WHIRLPOOL WRS588FIHZ00 New icemaker installed. Working properly.

Job Details:12/26/2018

REFRIGERATER WHIRLPOOL WRS321SDHW Cust popped filter door off when changing filter and could not figure out how to reset filter status LED. Instructed cust on how to reset filter status and i secured filter door. No further issue.

Job Details:12/26/2018

OVEN JENN-AIR JJW2830DP01 Panel control replaced tested ok

Job Details:12/26/2018

WASHER WHIRLPOOL WTW8800YW0 Check over found basket hub out position adjust tested with load all functions fine tub was replace on previous visit.

Job Details:12/26/2018

WASHER WHIRLPOOL WTW8540BW0 Replace all parts order test ok

Job Details:12/26/2018

DRYER MAYTAG MGDC200XW2 Dryer was flooded picture on record Inform cust must call home insurance

Job Details:12/26/2018

WASHER WHIRLPOOL WTW6700TW0 Customer not home must call or bill washer needs outertub leaking water will go for a new unit

Job Details:12/26/2018

DRYER WHIRLPOOL WGD5000DW3 Found vent pipe clog no air flow dryer check ok

Job Details:12/26/2018

GAS APPLIANCE MAYTAG MGDB850YG3 "CH - installed new console and control. Also, installed dryer repair kit from truck stock {4392067} - tests good. No other functional issues found at this time; used 1 4392067 (REPAIR KIT) from stock"

Job Details:12/26/2018

DISHWASHER MAYTAG MDB8959SFZ4Vd unit needs track (W11259786) track(W11259785)collected 193.33 by cc # owes 200 on return resc cust ; ordrng 1 W11259785 (TRACK) and 1 W11259786 (TRACK )

Job Details:12/26/2018

REFRIGERATOR JENN-AIR JFX2897DRM02 "Replaced freezer door,install kit,and seals,ok.Note: freezer door lighter shade of stainless..See pic.."

Job Details:12/26/2018

REFRIGERATOR WHIRLPOOL WRF555SDFZ03 Db installed parts tested unit unit ran to specs

Job Details:12/26/2018

DISHWASHER KITCHENAID KDFE204ESS1Db unit needs motor sump ; ordrng 1 WPW10605058 (SUMP MOTOR)

Job Details:12/26/2018

WASHER MAYTAG MVWX700XW1 CH - unit is not going in to agitate. Found stored f7e5 error - shifter fault. Verified voltage from control. Contunity test is good. Installed new actuator {WPW10006355} from truck stock. Calibrated unit and ran through diagnostic cycle - tests good. No other functional issues found at this time; used 1 WPW10006355 (ACTUATOR) from stock

Job Details:12/26/2018

MICROWAVE KITCHENAID KOCE500ESS05 Installed main control board defective relay on board tested unit ok

Job Details:12/26/2018

REFRIG/FREEZER GLADIATOR GAFZ30FDGB01 "Ep-installed new door, in original swing direction. Adjusted gasket for seal."

Job Details:12/26/2018

DISHWASHER JENN-AIR JDB1090AWS "Ep-unit drained when cancel was pressed. Ran diagnostics, no codes. Started “normal” cycle filled and started cycle, drained properly"

Job Details:12/26/2018

DISHWASHER WHIRLPOOL KDTM704ESS2 Installed top rack tracks testes unit ok

Job Details:12/26/2018

DISHWASHER WHIRLPOOL WDT750SAHZ0 Check unit install part that was order unit working fine

Job Details:12/26/2018

KITCHEN KITCHENAID KDTE404DSP "Installed new upper rack rails, tests good."

Job Details:12/26/2018

DISHWASHER MAYTAG MDB4949SDZ0Found wash motor making winding noise will need wash motor.; ordrng 1 WPW10591570 (WASH MOTOR)

Job Details:12/26/2018

KITCHEN WHIRLPOOL KDTM404EBS3 Replaced pump. Filled unit up twice and it drained as intended. No further issue.

Job Details:12/26/2018

REFRIG/FREEZER WHIRLPOOL WRF560SEYM02 "12/26/18 9:03: CS rspndd 12/24 MON, Replaced defective water tube ands unclogged icemaker fill tube. Unit working as designed"

Job Details:12/26/2018

REFRIGERATOR WHIRLPOOL GSC25C4EYB02 Cust stated at door that she canceled a week ago and no longer needed service.

Job Details:12/26/2018

DISHWASHER WHIRLPOOL WDF518SAFMordrng w10869127/overlay and wpw10567678/console (by SX)

Job Details:12/26/2018

OVEN WHIRLPOOL WFG530S0ES0 New control and temp sensor installed. Working properly.

Job Details:12/26/2018

WALL OVEN KITCHEN AID KODE300ESS00Installed inner glass ok will need thermostat lower oven not working after self clean; ordrng 1 WP4449751 (THERMOSTAT )

Job Details:12/26/2018

WASHER WHIRLPOOL LSQ9549LG0 "Installed motor,coupler and timer test ok..."

Job Details:12/26/2018

WASHER MAYTAG MVWC565FW1Customer in warrantee proof of purchase OK. Replaced actuator and motor unit still will not spin unit will need your keys and control as well as splotch.W11162438 control; ordrng 1 () and 1 W10721967 (drive pulley) and 1 W11035751 (gearcase)

Job Details:12/26/2018

WASHER WHIRLPOOL WFC7500VW2 "Removed debris from drain pump, rechecked functions and unit tested ok."

Job Details:12/26/2018

REFRIG/FREEZER WHIRLPOOL WRS321SDHZ01 Customer had rc control set on coldest settings ng. Adjusted it to reccomended.

Job Details:12/26/2018

REFRIGERATOR KITCHENAID KBSN608ESS00Spoke to tech line 773759416 ui isnt displaying proper temp will order ; ordrng 1 W10798007 (contrl-box)

Job Details:12/26/2018

DRYER MAYTAG MEDB835DW3Needs blower wheel and lint duct. ; ordrng 1 W10868982 (duct-lint) and 1 WP697772 (wheel)

Job Details:12/26/2018

OVEN WHIRLPOOL KSDB900ESS2"TB- Upon trying to remove, UI ribbon cable ripped. Also new console did not come with knob bezels. Additional parts needed for repair. New console was left with customer; will be installed in return. Rescheduled for Mon 12/31.; ordrng 1 W10814133 (BEZEL KIT) and 1 W11025616 (HARNESS)"

Job Details:12/26/2018

COOKTOP GS JENN-AIR JGC1530BS00 Found cap on wrong burner causing flames to shoot all over the place put the right cap on center burner tested ok no smell of gas.

Job Details:12/26/2018

DISPOSER WHIRLPOOL KCDI075B Customer will installed disposer

Job Details:12/26/2018

DISHWASHER WHIRLPOOL DU940PWKA0ordrng w10428776/motor and w10844024/inlet valve (by SX)

Job Details:12/26/2018

DRYER WHIRLPOOL FFIG3911QW1 Its a frigidaire dryer spoke to office we dont work on this brand

Job Details:12/26/2018

RANGE AMANA AGR5835QDQ Wpl74008682 front glass and lower trim 74008758 spoke to safety glass is nla ref number 773717787

Job Details:12/26/2018

RAN GS S/I WHIRLPOOL WEG760HODWH0"part was defective. Order parts, ordrng w11107275/ blower and w10885069/ pcb, used 1 w11107275 from stock (by XS)"

Job Details:12/26/2018

REFRIGERATOR WHIRLPOOL WRF757SDEM01CH - unit is not registering doors closing. Door switches test good. Unit needs new control {W10849460}; ordrng 1 W10849460 (CONTROL)

Job Details:12/26/2018

OVEN WHIRLPOOL WFG320M0BS3Oven ignitor is broken. ; ordrng 1 W11176454 (IGNITOR)

Job Details:12/26/2018

KITCHEN KITCHENAID KDPE234GPS0 Installed new sump/wash motor. Tests good.

Job Details:12/26/2018

DISHWASHER JENN-AIR JDB8200AWP3 Installed new user interface and control. Tests good.

Job Details:12/26/2018

REFRIGERATOR KITCHEN AID KUBL204ESB00 Installed rack correctly in unit

Job Details:12/26/2018

DISHWASHER KITCHEN AID KDTE254EWHO Manifold tubing replaced tested ok

Job Details:12/26/2018

REF T/M 10 CF WHIRLPOOL WRT111SFDM03 "Checked unit, adjusted thermostat in ff section to prevent food freezing. Also advised customer to put shims under front of unit because it is pitched forward causing door not to close properly. Unit test and check ok."

Job Details:12/26/2018

M/W OTR WHIRLPOOL WMH78019HZ0 Spoke to tech line 7723761385 advised nothing can be done

Job Details:12/26/2018

OVEN WHIRLPOOL WOS51EC0AS04 used 1 wpw10545255 from stock

Job Details:12/26/2018

WALL OVEN WHIRLPOOL KEBS277SSS04 Replaced defective panel.

Job Details:12/26/2018

REF S/S 25 CF WHIRLPOOL WRS325SDHZ00 Found hollow icecubes and very low pressure at dispenser..removed filter from bracket..pressure was alot better..customer will need to get a new filter..removed bin to clear it out and make sure all machanical parts were working ok...

Job Details:12/26/2018

REFRIGERATOR WHIRLPOOL WRS325FDAM02 "Replaced water filter housing m, tested ok..."

Job Details:12/26/2018

REFRIG/FREEZER WHIRLPOOL KSS048QMB01 "Made checks, cleaned ice dispenser bin, tested ok..."

Job Details:12/26/2018

OVEN WHIRLPOOL WFG505M0BS3 Installed part working fine

Job Details:12/26/2018

RANGE WHIRLPOOL MGT8775XS00TB- Unit needs replacement burner valve (front right). Customer paid in full $271.61 by cc ref 1392118048. No balance due on return. Customer rescheduled for Mon. 12/31.; ordrng 1 WPW10206287 (BURNER VALVE)

Job Details:12/26/2018

OVEN WHIRLPOOL WFG550S0HZ0 TB- Found front mounting screw for bake burner tube loose interfering with ignition grounding path and causing intermittent non-ignition. Corrected issue. Tests good.

Job Details:12/26/2018

DISHWASHER JENN-AIR JDTSS246GP0Ep-left side track has split and needs to be replaced. Ordering (1) W11259785 track. Currently held together by a zip tye; ordrng 1 W11259785 (TRACK)

Job Details:12/26/2018

DISHWASHER MAYTAG MDBH979SAM0 Installed door gasket brackets sealbarrier screw and spray arm tested unit fill wash drain ok no leaks at time of service

Job Details:12/26/2018

DISHWASHER JENN-AIR JDB9000CWS3"TB- Sump seal is deteriorating. All spray arms completely clogged with mold and debris. Needs replacement sump, spray arms and sump filters.; ordrng 1 W10872845 (FILTER CUP) and 1 W11101428 (LOWER SPRAY ARM) and 1 WPW10340542 (MANIFOLD) and 1 WPW10340745 (FEED TUBE) and 1 WPW10448645 (UPPER SPRAY ARM) and 1 WPW10463906 (FILTER SCREEN) and 1 WPW10605057 (SUMP ASSY)"

Job Details:12/26/2018

WASHER WHIRLPOOL WTW8000BW0 "Ep-unit had failed bearings. Replaced from truck stock, ran diagnostics. Functions as designed; used 1 W10435302 (BEARING) from stock"

Job Details:12/26/2018

OVEN KITCHENAID KEBC247KSS03TB- Unit needs replacement lower door latch. Customer paid $186.05 by check # 8608. Balance due on return is $186.05. Customer rescheduled for Wed. 1/2/18.; ordrng 1 WPW10195934 (LATCH)

Job Details:12/26/2018

WASHER MAYTAG MVWX655DW1 Rplc part test ok...

Job Details:12/26/2018

WASHER MAYTAG NTW4605EW0 Reset balance test ok..

Job Details:12/26/2018

RANGE WHIRLPOOL WFG520S0FS0 Assust gq with range tesred ok

Job Details:12/26/2018

COMPACTOR MAYTAG MTUC7500AFM0check and found that the engine and the switch-dir is damaged; ordrng 1 W10439651 (MOTOR-DRV) and 1 WP777811 (SWITCH-DIR)

Job Details:12/26/2018

REFRIG/FREEZER WHIRLPOOL WRB322DMB00 "Checked unit arm on the ice maker was in the off position, cycled IM dispenser ice and refilled, working ok"

Job Details:12/26/2018

WASHER WHIRLPOOL WGT4027HW0 Customer was concerned basket is to loose. Educated on new top load washers. Ran diagnostics and found no codes. Unit working properly.

Job Details:12/26/2018

OVEN WHIRLPOOL MGRH752BDW Installed new ignitor. Tests good. Collected remaining $157.24 by card.

Job Details:12/26/2018

LAUNDRY MAYTAG MVWB765FW0Ordering new control and ui. Code f2e1 lost communication error. Order W10919546 W10920541 W11199207; ordrng 1 W10919546 (console) and 1 W10920541 (cntrl-elec) and 1 W11199207

Job Details:12/26/2018

M/W OTR WHIRLPOOL WMH53521HZ0 All parts installed. All test ok.

Job Details:12/26/2018

RANGE KITCHENAID KSGB900ESS2"Ep-installed new control panel and tested function. Ordering bezels, unable to remove from original console; ordrng 1 W10814133 (BEZEL-KNOB)"

Job Details:12/26/2018

DISHWASHER KITCHENAID KDTE104ESS4ordrng x/sump & motor (by SX)

Job Details:12/26/2018

REF T/M 19 CFFF WHIRLPOOL n/a "Speak with customer at is door ,customer said is refrigerator is not giving him no problem is unit is working fine and he didn’t call for service"

Job Details:12/26/2018

RANGE WHIRLPOOL WMH53521HZI just found a mistake intslacion and the nut was broken; ordrng 2 W11122643 (NUT)s

Job Details:12/26/2018

REFRIGERATOR KITCHENAID KSC24C8EYY02 Replaced water tubing

Job Details:12/26/2018

REF T/M 18 CFFF MAYTAG MRT118FFFE01"Apt# C304. Checked unit, found food freezing in ff section. ; ordrng 1 W10838965 (THERMISTOR ) and 1 W11223735 (CONTROL BOX) and 1 WPW10384183 (THERMISTOR)"

Job Details:12/26/2018

RANGE - ELECTRIC WHIRLPOOL AGR5630BDS1 Found mouse traps all around the unit..did pull it out to checkthe control board area..also infested with mouse and roach droppings..causing electronics to short out..adviced customer her coverage is voided. Also would have to pay for any parts unit would need..she also agreed on the infestation issue..will get a new unit after infestation issue is addressed.

Job Details:12/26/2018

Kitchen WHIRLPOOL WFG320M0BS3 unit tested ok.

Job Details:12/26/2018

DISPOSER WHIRLPOOL KBDS250X4 "Checked and found unit has a loose screw jammed inside unit. Removed screw reset unit, unit works but still recommend replacing unit due to excess noise coming from it."

Job Details:12/26/2018

REFRIGERATOR KITCHEN AID KSSS42MDX00 Checked and found unit has multiple leaks causing unit to be low on freon.

Job Details:12/26/2018

D/WASHER UNDCTR KITCHEN-AID KDPM354GPS0 Educated cust.

Job Details:12/26/2018

REFRIG/FREEZER WHIRLPOOL KBBL206ESS01 Replaced freezer pan

Job Details:12/26/2018

RANGE WHIRLPOOL WFG320M0BS3 Installed parts job completed.

Job Details:12/26/2018

OVEN WHIRLPOOL KGRT6078BS1 "12/26/18 8:38: AR rspndd 12/24 MON, Checked unit and found defective regulator valve. Repair declined. If customer calls back please order wp9755424/valve $141.20 labor $120"

Job Details:12/26/2018

MICROWAVE KITCHEN-AID KMHS120ESSEcheck and found that the door switches are defective; ordrng 1 W10269458 (SWITCH) and 1 W10269460 (SWITCH) and 1 W10727360 (SWITCH )

Job Details:12/26/2018

MICROWAVE KITCHEN AID KMHS175MSS1check and I found that the magnetron is damaged; ordrng 1 8206317 (MAGNETRON)

Job Details:12/26/2018

DRYER WHIRLPOOL WGD75HEFW0"CH - extracted screws from console bracket and replaced. Installed dryer kit. Motor bearings are bad - unit is still vibrating heavily and making noise when run. Also, customer states that unit turned itself on again - could jot recreate that issue. Found no stored error codes. Unit needs new motor {W11086656}, wheel {WPW10211915}, control {W10875486}, extra time; ordrng 1 W10875486 (CONTROL) and 1 W11086656 (MOTOR) and 1 WPW10211915 (WHEEL)"

Job Details:12/26/2018

WASHER WHIRLPOOL CAE2745FQ0 Installed new outer tub tested ok advised customer of top being cracked before tech started repair

Job Details:12/26/2018

DRYER MAYTAG MGDC215EW2 Installed burner assembly and checked

Job Details:12/26/2018

RANGE WHIRLPOOL WFG320M0BW0 Part installed..instructed customer not to lay any5i g on this door..also not to push door to far down...test ok while present.

Job Details:12/26/2018

M/W OTR WHIRLPOOL WMH76719CS5Note door dented in two places install anyway so that customer can use microwave .and install control electric..need to reorder door..; ordrng 1 W10893441 (door/mw)

Job Details:12/26/2018

DRYER WHIRLPOOL WGD4850BW0 -Removed obstruction from blower wheel houses ng-adjusted blower wheel

Job Details:12/26/2018

OVEN WHIRLPOOL WFG320M0BS3 Unit tested & checked oven light defective . Bulb separated from base.Removed base from socket Cx will re install new bulb.